Siemens SINUMERIK 802D sl Manual do Operador descarregar pdf (Página 35)

NCK alarms

06/2009 Overview of alarms

2-35

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

6431 [Channel %1: ] Block %2 Function not allowed. Tool

management/monitoring is not active.

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: Occurs when a data management function is called which is not available because ToolMan is deac-

tivated. For example, the language commands GETT, SETPIECE, GETSELT, NEWT, DELT.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: - Please inform the authorized personnel/service department.

- Make sure of how the NC is supposed to be configured! Is tool management or tool monitoring

needed but not activated?

- Are you using a part program that is meant for a numerical control with tool management/tool mon-

itoring? It is not possible to start this program on the numerical control without tool management/tool

monitoring. Either run the part program on the appropriate NC control or edit the part program.

- Activate tool management/tool monitoring by setting the appropriate machine data. See

MD18080$MN_MM_TOOL_MANAGEMENT_MASK,

MD20310$MC_TOOL_MANAGEMENT_MASK

- Check whether the required option is set accordingly.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

6500 NC memory full

Definitions: The NCK file system is full.

The available buffered memory does not suffice. Note: At initial start-up, files of the NC file system

may be affected such as drive data, HMI files, FIFO files, NC programs...

Reaction: Alarm display.

Remedy: Adjust the size of the buffered memory (MD18230 $MN_MM_USER_MEM_BUFFERED) or increase

the space available in the buffered memory, e.g. by unloading part programs that are no longer being

used. Or decrease the size of the ring buffer (see $MC_RESU_RING_BUFFER_SIZE).

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

6510 Too many part programs in the NC memory

Definitions: The number of files in the file system (part of the NC memory) of the NC has reached the maximum

number possible. Note: During initial start-up, this can concern files from the NC file system, e.g. drive

data, HMI files, FIFO files, NC programs, ...

Reaction: Alarm display.

Remedy: Please inform the authorized personnel/service department.

- Delete or unload files (e.g. part programs), or

- Increase MD18320 $MN_MM_NUM_FILES_IN_FILESYSTEM.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

6530 Too many files in directory

Definitions: The number of files in a directory of the NC memory has reached the maximum limit.

Reaction: Alarm display.

Remedy: Please inform the authorized personnel/service department.

- Delete or unload files (e.g. part programs) in the respective directory, or

- Increase MD18280 $MN_MM_NUM_FILES_PER_DIR.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

6540 Too many directories in the NC memory

Definitions: The number of directories in the NC file system (part of the NC memory) has reached the maximum

limit.

Reaction: Alarm display.

Remedy: - Delete or unload directory (e.g. workpiece), or

- Increase MD18310 $MN_MM_NUM_DIR_IN_FILESYSTEM.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 339 340

Comentários a estes Manuais

Sem comentários

Siemens SINUMERIK 802D sl Manual do Operador Página 35

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Siemens SINUMERIK 802D sl