Siemens SINUMERIK 802D sl Manual do Operador descarregar pdf (Página 281)

PROFIBUS alarms

06/2009 Overview of alarms

2-281

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

2.4 PROFIBUS alarms

380001 PROFIBUS/PROFINET: Startup error, reason %1 parameter %2 %3 %4.

Parameters: %1 = Cause of the error

%2 = Parameter 1

%3 = Parameter 2

%4 = Parameter 3

Definitions: An error occurred during startup of the PROFIBUS/PROFINET master.

Overview: Cause of the error, Par 1, Par 2, Par 3:

- 01 = DPM version, DPM version, DPA version, --

- 02 = DPM ramp-up timeout, DPM actual value status, DPM setpoint value status, --

- 03 = DPM ramp-up status, DPM actual value status, DPM setpoint value status, DPM error code

- 04 = DPM ramp-up error, DPM actual value status, DPM setpoint value status, DPM error code

- 05 = DPM-PLL sync error, --, --, --

- 07 = Alarm queue too long, Actual number, Setpoint number, --

- 08 = Unknown client, Client ID, --, --

- 09 = Client version, Client ID, Client version, DPA version

- 10 = Too many clients, Client number, max. number of clients, --

- 11 = Log.basic address used several times; bus no.; slot no.; log.basic address --

- 20 = Slave/device address used several times, slave/device address --

- 21 = Slave/device address unknown, slave/device address, --

- 22 = Erroneous configuration telegram, slave/device address, error code, --

- 23 = OMI incompatible (data), drive version, CDA version, --, --

- 24 = OMI incompatible (driver), drive version, CDA version, --, --

- 25 = CPI initialization failed, error code, --, --, --

- 26 = DMA not active

- 27 = Reserved

- 28 = Reserved

- 29 = Reserved

- The 1000s digit of the error cause = number of the affected bus

Clients are the following components of the control system that use the PROFIBUS/PROFINET:

Client ID = 1: PLC

Client ID = 2: NCK

Possible causes are:

- Error in contents of SDB

- Corruption of parts of the system program

- Hardware defect on NC component

Reaction: Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Remedy for 1-11

1. Check the control project, check MD11240 $MN_PROFIBUS_SDB_NUMBER, and reload it when

using a user-specific SDB.

2. If the error still occurs, back up data, and restart the control with the standard values as per the as-

delivered condition.

3. In case of correct ramp-up, reload the user data stage by stage.

4. If the error still occurs during ramp-up with standard values, reboot the system from the PC card or

update the software.

5. If the error still occurs, replace the hardware.

Remedy for 20-21

1. Check/correct the addresses of the connected slaves/devices.

Remedy for 22

See SINAMICS warning 1903 for a description of the meaning behind the error codes.

1. Control the SDB

- Check the type and length of the message frame

- Match slot assignment with P978

2. Evaluate the drive alarms/warnings

Remedy for 23-24

1. Software replacement required

Remedy for 25

1 2 ... 276 277 278 279 280 281 282 283 284 285 286 ... 339 340

Comentários a estes Manuais

Sem comentários

Siemens SINUMERIK 802D sl Manual do Operador Página 281

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Siemens SINUMERIK 802D sl