Siemens SINUMERIK 802D sl Manual do Operador descarregar pdf (Página 245)

Cycle alarms

06/2009 Overview of alarms

2-245

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

61441 [Channel %1: ] Block %2: Position of cutting edge is not in the machining

plane.

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycle: CYCLE982

Remedy: The position of the cutting edge of the turning tool (cutting tip) is no longer in the machining plane

(interpolation plane), this can be caused, for example, by a tool carrier with orientation capability. Cor-

rect the tool carrier position.

61442 [Channel %1: ] Block %2: Tool carrier not parallel to the geometry axes

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycle: CYCLE982

Remedy: As a result of incorrect positioning of the orientable tool carrier, tool lengths L1,2,3 are not parallel to

the geometry axes.

Optimize the axes of the tool carrier.

61443 [Channel %1: ] Block %2: Advance angle _INCA=0 or greater/less than +/-

90° or +/-120°

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycle: CYCLE979

Remedy: Check the value in the parameter advance angle _INCA.

If 3-point measurement is selected, _INCA must not be greater/less than +/-120°, and with 4-point

measurement _INCA must not be greater/less than +/-90°.

The advance angle _INCA must always be parameterized unequal to "zero".

61444 [Channel %1: ] Block %2: Current measuring speed is not identical to the

calibration speed

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following measuring cycles: CYCLE974, CYCLE994, CYCLE977,

CYCLE978, CYCLE979, CYCLE997, CYCLE998

E_MS_CAN, E_MS_HOL, E_MS_POC, E_MS_PIN, E_MS_SPI

Remedy: 1. Repeat the calibration on the basis of the desired measuring speed.

2. Match the current measuring speed to the calibration speed.

Note: In each case, the relevant calibration speed is stored in each calibration data record.

61501 [Channel %1: ] Block %2: Simulation is active

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following grinding cycles: all grinding cycles

Remedy: Reset simulation

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61502 [Channel %1: ] Block %2: No tool offset active

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following grinding cycles: all grinding cycles

Remedy: A tool number must be programmed

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

61503 [Channel %1: ] Block %2: tool nose radius compensation left or right

Parameters: %1 = Channel number

%2 = Block number, label channel number

Definitions: The alarm can be triggered by the following grinding cycles: CYCLE410, CYCLE411, CYCLE412,

CYCLE413, CYCLE414, CYCLE415, CYCLE416, CYCLE420

1 2 ... 240 241 242 243 244 245 246 247 248 249 250 ... 339 340

Siemens SINUMERIK 802D sl Manual do Operador Página 245

Comentários a estes Manuais

Siemens SINUMERIK 802D sl Manual do Operador Página 245

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Siemens SINUMERIK 802D sl