Siemens SINUMERIK 802D sl Manual do Operador descarregar pdf (Página 119)

NCK alarms

06/2009 Overview of alarms

2-119

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

Remedy: - Modify part program.

- If new cycle programs have been loaded on the NCK, you will normally need to increase the values

of MD18170 $MN_MM_NUM_MAX_FUNC_NAMES and MD18180

$MN_MM_NUM_MAX_FUNC_PARAM. See also the explanations for alarm 6010.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

15180 [Channel %1: ] Block %2: Error on editing program %3 as INI/DEF file.

Parameters: %1 = Channel number

%2 = Block number, label

%3 = String

Definitions: Errors were found when processing an initialization program (INI file), or a GUD or macro definition

file (DEF file).

The error message which is then displayed refers to the program specified here.

Reaction: Alarm display.

Remedy: Correct the initialization program (INI file), or the GUD or macro definition file (DEF file).

In connection with Alarm 12380 or 12460, also change the memory configuration.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

15185 [Channel %1: ] %2 errors in INI file

Parameters: %1 = Channel number

%2 = Number of detected errors

Definitions: Errors were found when processing initialization program _N_INITIAL_INI.

This alarm will also be output, if errors are found during editing of _N_INITIAL_INI in the GUD defini-

tion files or if errors are found on ramp-up in the macro definition files.

Reaction: NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Please inform the authorized personnel/service department. Correct the INI or DEF file or correct the

MD and create a new INI file (via "Upload").

Program Con-

tinuation:

Switch control OFF - ON.

15190 [Channel %1: ] Block %2 not enough free memory for subroutine call

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: The following deadlock has been found in the interpreter: Memory is needed for calling a subroutine.

The module memory is, however, empty and there is no prospect of module memory becoming free

again by executing the preprocessing/main run queue, because this queue is empty.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Please inform the authorized personnel/service department. Increase machine data MD28010

$MC_MM_NUM_REORG_LUD_MODULES / MD28040 $MC_MM_LUD_VALUES_MEM / MD18210

$MN_MM_USER_MEM_DYNAMIC or program a preprocessing stop STOPRE before calling the sub-

routine.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

15300 [Channel %1: ] Block %2 invalid number-of-passed-blocks during block

Parameters: %1 = Channel number

%2 = Block number, label

Definitions: In the function "Block search with calculation" a negative number of passes has been entered in col-

umn P (number of passes). The permissible range of values is P 1 - P 9 999.

Reaction: Alarm display.

Remedy: Enter only positive number of passes within the range of values.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

1 2 ... 114 115 116 117 118 119 120 121 122 123 124 ... 339 340

Comentários a estes Manuais

Sem comentários

Siemens SINUMERIK 802D sl Manual do Operador Página 119

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Siemens SINUMERIK 802D sl