Siemens SINUMERIK 802D sl Especificações descarregar pdf (Página 104)

Overview of alarms 06/2007

NCK alarms/ISO alarms

2-104

SINUMERIK 802D sl, Diagnostics Manual, 06/2007Edition

Remedy: Correct the name used (writing error)

$TC_DPCx, $TC_TPCx, $TC_MOPCx, $TC_MAPCx, $TC_MPPCx, $TC_DPCSx, $TC_TPCSx,

$TC_MOPCSx, $TC_MAPCSx, $TC_MPPCSx; with x=1,...10

These are the OEM parameters of the tools and magazines, the corresponding machine data value is

set to < 10, or the option 'TM OEM parameters' has not been set.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12553 Channel %1 block %2 name %3 option/function is not active

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Source symbol

Definitions: The NC function that belongs to this language command is not active. Although the name of the lan-

guage command is known, the use of this language command in any program is rejected with this

alarm.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECT. The correction pointer positions on the incorrect block.

• Correct the name used (typing error)

• Activate the NC function.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12554 Channel %1 block %2 replacement cycle %3 for the predefined

procedure is missing.

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Cycle name

Definitions: The replacement cycle that is to be called instead of the predefined procedure

is not present / unknown in the control.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC stop key and select the "Compensation block" function by pressing the PROGRAM

CORRECT softkey. The cursor will position itself in the faulty block.

- Correct the name used for the predefined procedure (write error)

- Or load the replacement cycle into one of the cycle directories (+ restart)

- Or set the machine data bit for the predefined procedure in $MN_COUPLE_CYCLE_MASK to 0 so

that the predefined procedure is executed again.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12555 Channel %1 block %2 function not available (identification %3)

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Detailed identification

Definitions: The identifier is not defined for this system.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECT. The correction pointer positions on the incorrect block.

- Correct the name used (typing error)

- For low-level functions, use a more advanced software system

- Check definitions of variables, subroutines and macros

- Declare subroutine with EXTERN, load subroutine to SPF-Dir

- Check interface definition of subroutine

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 391 392

Comentários a estes Manuais

Sem comentários

Siemens SINUMERIK 802D sl Especificações Página 104

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Siemens SINUMERIK 802D sl