Siemens SITRANS P Instruções de Operação Página 76
- Página / 234
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Function Mode Key function Display, explanations
[M] [↑] [↓] [↑] and [↓]
Key lock or function
lock
10 Switch between the five
functions
– 0 None
LA all locked
LO all locked except for start of scale value
LS all locked except for start of scale value
and full scale value
L Write protection
Operation via HART not possible.
Characteristic
curve
1)
11 Switch between the four
functions
linear lin linear
srlin square root extracting (linear up to the
application point)
sroff Square root extracting
(deactivated
up to the application point)
srli2 square root extracting (linear up to the
application point 10%)
Application point of
the square root
extracting
characteristic curve
1)
12 Greater Smaller 10% flow rate Adjustment range of 5 to 15% flow rate.
Measured value
display
13 Select from three options. – ● Display type (input value)
●
Output current in mA
● Measured value in %
Unit 14 Select from the table for
measured value display.
In each case,
the
first value
from the table
of the
physical unit
Physical unit
1)
Not relevant for gauge and absolute pressure)
See also
Overview of operation
(Page 65)
Operating functions through HART communication (Page 99)
6.5.2 Operation using buttons
Introduction
This overview informs you about the most important safety notes to be observed when
operating the pressure transmitter. Furthermore, the overview guides you in adjusting the
operating functions on site.
Condition
The keyboard must have been unlocked in order to operate the device using the buttons.
Operation
6.5 Local operation
SITRANS P, DS III series with HART
74 Operating Instructions, 09/2012, A5E00047092-08
- Pressure transmitter 1
- Table of contents 10
- 1.4 Scope of the instructions 12
- 1.5 Checking the consignment 12
- 1.7 Notes on warranty 13
- Safety instructions 15
- 2.2 Use in hazardous areas 16
- 3.2 Application range 20
- 3.3 Structure 21
- 3.4 Nameplate layout 23
- SITRANS P 24
- 3.6 Functional principle 25
- Overview 26
- 3.7 Remote seal 33
- 3.8 SIMATIC PDM 33
- Installing/mounting 35
- 4.1 Basic safety instructions 36
- ① Flameproof joint 37
- 4.1.2 Proper mounting 40
- 4.2 Disassembly 41
- Installation configuration 42
- 4.3.3 Fastening 43
- Requirements 45
- 4.4.2 Installation for level 46
- Assembly on an open container 47
- 4.7 Rotating the display 57
- Connecting 59
- 5.1 Basic safety instructions 60
- Connecting the device 62
- Closing the device 63
- 5.3 Connecting the Han plug 64
- ④ Shrink sleeve 66
- ② Positioning catch 66
- Operation 67
- Basic safety instructions 68
- 6.4 Display 69
- 6.4.2 Units display 70
- 6.4.3 Error display 71
- 6.4.4 Mode display 72
- 6.4.5 Status display 72
- 6.4.6 Overflow range 73
- 6.5 Local operation 74
- Operating functions 75
- 6.5.2 Operation using buttons 76
- Setting start of scale value 81
- Adjusting full scale value 83
- Differences 85
- Blind adjusting 85
- Example of blind adjusting 85
- 6.5.6 Trimming the zero point 89
- 6.5.7 Current transmitter 90
- Releasing key lock 93
- Variable application point 94
- Fixed application point 94
- 6.5.12 Measured value display 96
- 6.5.13 Unit 97
- Condition 101
- Introduction 101
- Fundamental description 101
- See also 101
- 7.2 Process tag data 102
- 7.3.2 Measuring mode selector 103
- 7.3.3 Variable mapper 103
- Description 105
- DV Device variable 106
- MA Start of scale value 106
- ME Full scale value 106
- 7.3.9 Measured value status 112
- UNCERTAIN status 113
- HIGH LIMIT and LOW LIMIT 113
- Change in status 113
- LIMIT are swapped around 115
- 7.3.10 Analog output 116
- Procedure 119
- 7.7 Electrical damping 120
- 7.8 Fast response mode 120
- 7.9 Current sensor 120
- 7.10 Fault current 120
- Lock options 122
- 7.13 Measured value display 123
- 7.15 Bar graph 125
- 7.16 Sensor calibration 125
- Current sensor trim 126
- Factory calibration 127
- Static configuration data 128
- 7.21 Diagnostic functions 130
- &DOLEUDWLRQLQWHUYDO 131
- 6WDELOLW\PRQWK 131
- 3UHVVXUHFXUYH 132
- 8SSHUGUDJLQGLFDWRUSRLQW 132
- /RZHUGUDJLQGLFDWRUSRLQW 132
- 7.21.5 Limit modules 133
- 7.22 Simulation 135
- 7.23 Limit monitor 136
- Functional safety 139
- Operational reliability 141
- 8.2.1 Safety function 142
- 8.2.2 Settings 142
- 8.2.3 Requirements 143
- 8.2.5 Maintenance/Checking 144
- 8.2.6 Safety characteristics 144
- 8.3.1 Safety function 145
- 8.3.2 Requirements 146
- 8.3.3 Settings 147
- 8.3.5 Maintenance/Checking 148
- 8.4 Add-on parts 149
- Commissioning 151
- Requirement 155
- Service and maintenance 161
- 10.2.2 Checking the gaskets 165
- 10.3 Cleaning 166
- Cleaning the enclosure 167
- 10.4 Return procedure 168
- 10.5 Disposal 168
- Technical data 171
- 11.2 Input point 172
- 11.3 Output 179
- 11.4 Measuring accuracy 179
- 11.5 Operating conditions 185
- 11.6 Construction 189
- 11.9 HART communication 196
- Dimension drawings 197
- ① Key cover ⑤ Connection side 204
- 12.4.1 Note 3A and EHDG 205
- Flanges as per ASME 206
- Connections as per DIN 206
- Other connections 208
- BioConnect 208
- connectors 208
- 12.4.4 PMC Style 210
- 12.4.5 Special connections 211
- IDF connectors 212
- Spare parts/accessories 213
- 13.1 Order data 214
- Appendix 217
- A.3 Literature and catalogs 218
- A.5 Technical support 222
- List of abbreviations 223
- B.1 Functional safety 224
- Glossary 225
- Failure/Fault 226
- Frequency shift keying 226
- $( 234
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais