Siemens Sinumerik 810T Manual do Utilizador descarregar pdf (Página 79)

EMCO WINNC SINUMERIK 810/820 T ALARMS / MESSAGES

H 3

2046 Block greater than 120 characters

Cause: NC block is too long (with loading a pro-

gram)

Remedy: divide NC block in several blocks with DOS

editor

2048 Nxxxx Circle end point error

Cause: invalid circle, invalid circle centre, radius

too small

Remedy: correct program

2060 Nxxxx Pogramming error TO, ZO

Cause: D number too great, tool type not allowed

Remedy: correct program

2061 Nxxxx General program error

Cause: NC block structure wrong, block number,

M/H/G code not allowed, invalid combina-

tion of G commands, radius/dwell program-

med twice, dwell time too long, circle already

programmed, general block structure error

with calculating operation

Remedy: correct program

2062 Nxxxx Feed missing / not progr.

Cause: F value too great, attempt to start with F=0,

also with G95/96, if S=0 or M5

Remedy: correct program

2063 Nxxxx Thread lead to high

Cause: thread pitch too great / missing, feed with

threads reaches 80% of rapid speed

Remedy: correct program, smaller pitch or lower

speed with threads

2065 Nxxxx Pos behind SW overtr. switch

Cause: target point programmed out of software

end switch or circle path overtravels

software end switch

Remedy: correct program

2068 Nxxxx Pos behind working area

Cause: target point programmed out of working area

Remedy: correct program

2072 Nxxxx Incorrect input value

Cause: chamfer/radius too large

Remedy: correct program

2073 Nxxxx No intersection point

Cause: no intersection point with contour definition

arc-line

Remedy: correct program

2074 Nxxxx Wrong angle value

Cause: no contour draft is possible with that angle

Remedy: correct program

2075 Nxxxx Incorrect radius value

Cause: wrong circle centre point or radius

Remedy: correct program

2076 Nxxxx Wrong G02/G03

Cause: wrong rotational direction for tangential

draft arc-line programmed

Remedy: correct program

2077 Nxxxx Incorrect block sequence

Cause: chamfer/radius: no 2. traverse block was

programmed

Remedy: correct program

2081 Nxxxx CRC not allowed

Cause: thread, change of correction direction/mirror

axis/tool correction not allowed with CRC,

circle not in selected CRC plane, change of

plane while CRC

Remedy: correct program

2082 Nxxxx CRC not determinable

Cause: plane change CRC not allowed, invalid

contour element, contour violation full circle,

contour element too short

Remedy: correct program

2160 Nxxxx Scale factor not allowed

2171 Nxxxx Approach not possible

Cause: no tool correction, tool radius = 0 (CRC)

Remedy: select tool, enter tool radius in tool data

2172 Nxxxx Retract not possible

Cause: error with selection CRC

Remedy: correct program

2501 ORDxx Synchronisation-error AC

Remedy: RESET, report to EMCO if repeatable

2502 ORDxx Synchronisation-error AC

Remedy: RESET, report to EMCO if repeatable

2503 ORDxx Synchronisation-error AC

Remedy: RESET, report to EMCO if repeatable

2504 ORDxx Insuff. RAM for interpreter

Cause: not enough RAM memory, continuation of

the program not possible

Remedy: close all other WINDOWS applications,

cease program, remove resident programs

(from AUTOEXEC.BAT and CON-

FIG.SYS), restart PC

2505 ORDxx Insuff. RAM for interpreter

see 2504

2506 ORDxx Insufficient RAM

see 2504

2507 ORDxx Referencepoint not active

Remedy: approach reference point

2508 ORDxx Intenal error NC core

Remedy: RESET, report to EMCO if repeatable

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 89 90

Comentários a estes Manuais

Sem comentários

Siemens Sinumerik 810T Manual do Utilizador Página 79

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Siemens Sinumerik 810T