Siemens EK 726 Series Manual de Serviço descarregar pdf (Página 80)

COMMUNICATIONS / INTERFACES

MICROMASTER

MICROMASTER Vector

MIDIMASTER Vector

SIEMENS DA 64 – 2001/2002

Version C4 4/4

The operator panel is automatically activated as soon as it is

connected to a drive inverter or the voltage is switched-on.

Dimensions H x W x D 130 mm x 73 mm x 40 mm

Current drain at 5 V 200 mA

Degree of protection IP 54

Max. cable length 5 m

Table 2: Technical data

LCD

display

CLOCKWISE/COUNTER

CLOCKWISE

key

OFF

key

ON/OFF

display

JOG

key

Increase frequency

Decrease frequency

Parameterization

key

Jog

RUN STOP

key

P000 RUNNING ®

RPM=1250

F=50.00Hz

I=1.5A M=125% P ×

The keys have the same functions as on the standard

operator panel; the exception is the MENU key, with which the

main menu screen can always be selected. Information on

which key should be pressed is provided in the righthand

screen column.

All of the main functions are accessible from the main menu

screen.

OPERATE UPREAD

DIAG. DOWNLOAD

PARAMS LANGUAGE

MODE CONFIG.

Operating display

Diagnosing

drive

faults

Parameteriz.

the drive

Mode selected for the module:

Local, master, internal, RS232-RS485 conversion

Reading the parameter groups

from the drive into the module

Reading the parameter groups

from the module into the drive

Language selection

Config. module functions:

Back lighting, contrast,

large numbers, cursor, help,

zero positions

Fig. 5.3: Main menu screen

A help screen is displayed by simultaneously pressing the

menu and the Ú key. The help screen displays the main

functions of the plain text display module.

When powered-up, unless otherwise configured, the operating

display appears.

STOPPED

P000 S=50.00Hz

I=0.0A RPM=0

V=0.0V

Drive status:

Stopped, running,

fault, alarm

Motor direction

of rotation

Output frequency

(alternating with the setpoint

if the motor is stopped)

Motor actual speed

Motor voltage

Motor

current

Operating display in the LOCAL mode

RUNNING P

F=50.00Hz

Drive status:

Stopped, running,

fault, alarm

Output frequency

(alternating with the set-

point if the drive is stopped)

Motor direction

of rotation

Drives connected to the USS bus,

in this case 0, 7 and 16 can be

selected using the arrow keys

ctivates the data transfer

function to start or stop all

drives connected to the

bus

Operating display in the MASTER mode

The status LED indicates whether the drive is presently

running. If the LED is green, the drive runs; if it is red, the

drive was stopped.

If the drive parameters are accessed, the help texts are linked

with the parameter and the parameter values.

Indicates that inter-

nally saved param.

quantities are being

acccessed

Text which descr.

the selected param.

PARAMS All

P051= 1

SELECT DIG I/P 1

run right h

Parameter

number

Indicates that higher or lower

parameter values are available

Text which describes the

selected value

Parameter

access

Parameter group:

ll, general, motor rating plate,

ramps, PID, setpoint,

frequency, I/O, comms., user

set-up, changing standard

settings

4.5.2 RS232 interface

The plain text operator panel is equipped with an RS232

interface which allows the drive to be connected to a PC.

1 2 3 4 5

+6V

Fig. 4: Pin assignment of the RS232 connector

Pin Function, information

1 Not assigned

2 External TxD

3 External RxD

4 External RTS

5 Insulated 0V

Power supply to operate an OPM2

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 119 120

Comentários a estes Manuais

Sem comentários

Siemens EK 726 Series Manual de Serviço Página 80

Comentários a estes Manuais

Manuais e produtos relacionados com Fogões Siemens EK 726 Series