Siemens Simatic M7-400 Manual do Utilizador descarregar pdf (Página 126)

SIMATIC S7-400

SIPLUS communication

SIPLUS CP 443-1 Advanced

6/126

Siemens ST 70 · 2013

■

Overview

• Connection of SIMATIC S7-400 to Industrial Ethernet

- Multi-protocol operation for ISO, TCP/IP, UDP and

PROFINET IO protocols

- Adjustable keep-alive function

• Two separate interfaces (integrated network separation):

- Gigabit interface with one RJ45 port with

10/100/1 000 Mbit/s, full/half-duplex with auto-sensing

capability

- PROFINET interface with four RJ45 ports with 10/100 Mbit/s,

full/half duplex with autosensing and autocrossover function-

ality via integrated 4-port switch

• Communication services via both interfaces

- Open communication (ISO, TCP/IP and UDP), multicast with

UDP, including routing between both interfaces

- PG/OP communication:

Cross-network by means of S7 routing

- S7 communication (client, server, multiplexing) including

routing between both interfaces

- IT communication:

HTTP communication supports access to process data via

own Web pages;

e-mail client function, sending of e-mails with authentication

directly from user program;

FTP communication supports program-controlled FTP client

communication;

access to data blocks through FTP server

• Communication services via PROFINET interface

- PROFINET IO controller with real-time properties

(RT and IRT)

- PROFINET CBA

- IP address assignment via DHCP, simple PC tool or via the

user program (e.g. HMI)

- Support of the prioritized startup of PROFINET IO devices

- Configuration with STEP 7

• Media redundancy (MRP);

the CP supports the media redundancy procedure MRP within

an Ethernet network with ring topology.

• Access protection by means of configurable IP access list

• Module replacement without programming device;

all information is stored on the C-PLUG

(also file system for IT functions)

• Extensive diagnostic functions for all modules in the rack

• Integration into network management systems through the

support of SNMP V1 MIB-II

• Operation in the SIMATIC H system for redundant S7-commu-

nication

• Operation in fail-safe applications (PROFIsafe) in combination

with SIMATIC S7-400 CPU 416F

Note:

SIPLUS extreme products are based on Siemens Industry

standard products. The contents listed here were taken from the

respective standard products. SIPLUS extreme specific infor-

mation was added.

For technical documentation on SIPLUS, see:

www.siemens.com/siplus-extreme

*B,.B;;B

663*23,35,7053317&3

8'3

,62

SIPLUS CP 443-1 Advanced

Order No. 6AG1 443-1GX20-4XE0

Order number based on 6GK7 443-1GX20-0XE0

Ambient temperature range

0...+60 °C

Conformal coating Coating of the printed circuit boards

and the electronic components

Technical data

The technical data of the standard

product applies, except for the

ambient conditions

Ambient conditions

Relative humidity

100%, condensation/frost permissi-

ble. No commissioning if condensa-

tion present.

Biologically active substances,

compliance with EN 60721-3-3

Class 3B2 mold and fungal spores

(excluding fauna). The supplied

plug covers must remain in place

over the unused interfaces during

operation!

Chemically active substances,

compliance with EN 60721-3-3

Class 3C4 incl. salt spray in accor-

dance with EN60068-2-52 (degree

of severity 3). The supplied plug

covers must remain in place over

the unused interfaces during opera-

tion!

Mechanically active substances,

compliance with EN 60721-3-3

Class 3S4 incl. sand, dust. The sup-

plied plug covers must remain in

place over the unused interfaces

during operation!

Air pressure (depending on the

highest positive temperature range

specified)

1 080 ... 795 hPa

(-1 000 ... +2 000 m)

see ambient temperature range

795 ... 658 hPa

(+2 000 ... +3 500 m)

derating 10 K

658 ... 540 hPa

(+3 500 ... +5 000 m)

derating 20 K

Kap_06_eng.book Seite 126 Donnerstag, 2. Mai 2013 4:16 16

1 2 ... 121 122 123 124 125 126 127 128 129 130 131 ... 157 158

SIMATIC S7-400 1

Comentários a estes Manuais

Sem comentários

Siemens Simatic M7-400 Manual do Utilizador Página 126

Comentários a estes Manuais

Manuais e produtos relacionados com Medição, teste e controlo Siemens Simatic M7-400