Siemens SIMATIC TI500 Especificações Página 275
- Página / 322
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Upgrading Existing Series 500 Installations
C-16
SIMATIC 545/555/575 System Manual
Installing a PPX:500–5114–A RBC (continued)
As shown in Figure C-7, the display at the top of the module indicates the
status of the Series 500 RBC.
Baud rate thumbwheel
Base thumbwheel
LED display
Remote
Base
Controller
Thumbwheel Baud
Number Rate
0 9600. . . . . . . .
1 2400. . . . . . . .
2 1200. . . . . . . .
3 300. . . . . . . . .
4 19200. . . . . . .
5 19200. . . . . . .
6 19200. . . . . . .
7 19200. . . . . . .
8 9600. . . . . . . .
9 2400. . . . . . . .
10 1200. . . . . . . .
11 300. . . . . . . . .
12 19200. . . . . . .
13 19200. . . . . . .
14 19200. . . . . . .
15 19200. . . . . . .
RS-485 I/O port 9-pin female
RS-232 port 25-pin female
Figure C-7 Series 500 Remote Base Controller and Baud Rate Settings
Status is displayed in integer format; see Table C-2 for definitions.
Table C-2 Series 500 RBC LED Messages
Display Definitions Display Definitions
0 RBC Good 5 Not Used
1 Self Diagnostics Failure 6 Not Used
2 Module Mismatch 7 Communication Good, Not
Configured
3 I/O Communication Time
Out
8 Watchdog Timer Expired
4 RAM Parity Error
The RBC is equipped with a RS-232 port that allows you to program the
Series 505 CPU or to troubleshoot from a remote I/O base. A baud rate
thumbwheel, shown in Figure C-7, is used to set the baud rate for this port.
Status Display
Setting Baud Rates
- 1
- 1
- MANUAL PUBLICATION HISTORY 3
- LIST OF EFFECTIVE PAGES 4
- Contents 5
- Contents v 7
- Contents vii 9
- Contents ix 11
- Chapter 9 Troubleshooting 12
- Contents xi 13
- List of Figures 15
- Contents xv 17
- List of Tables 18
- Contents xvii 19
- System Overview 23
- 1.1 Overview 24
- Overview (continued) 26
- 1.2 System Features 28
- Table 1-2 CPU Specifications 29
- System Features (continued) 30
- 1.3 Programming Tools 33
- 1.4 Hardware Overview 34
- Pre-installation Guidelines 36
- 2.2 Safety Considerations 38
- 2.3 575 Fault Relay Operation 41
- USER-CONFIGURED 42
- 2.5 Electrical Noise 47
- 2.6 Correcting Noise Problems 48
- 2.7 Wiring Guidelines 51
- Chapter 3 56
- To install a CPU: 57
- To install an RBC: 57
- 3.3 Series 505 Bases 59
- Measurements: 62
- TAB1TAB2 64
- DC POWER GOOD 66
- AC NEUTRAL 66
- 505-6660 66
- Replaceable Lithium Battery 71
- Replaceable 73
- Lithium Battery 73
- Battery Clip 73
- Battery Socket 73
- 0 (Off)(On) 1 77
- Maximum torque: 82
- 5.0 in-lb (0.56 N-m) 82
- Chapter 4 84
- • Series 505 Remote I/O Annex 85
- • PROFIBUS-DP Annex 85
- Front of Fan Assembly 91
- Fuse holder 92
- Turn counterclockwise 92
- (Run mode) 4.875 to 5.250 1 A 98
- (Battery 98
- Align metal backplate 100
- 4.8 Installing the Battery 103
- Battery connector 104
- Rear panel 104
- Break-away tab 104
- Battery fuse 105
- Alignment 106
- Alignment notch 106
- 4.10 Configuring the CPU 107
- Dipswitch 112
- Standoff 112
- 4.12 Installing VMEbus Boards 115
- 575 system 116
- Figure 4-18 575 Controller 116
- 4.13 Wiring the Fault Relay 127
- *optional 128
- Chapter 5 142
- 5.1 Overview 143
- 5.2 Installation 144
- Installation (continued) 145
- 5.3 Communication Ports 146
- Dipswitch for 149
- Backplane 149
- Figure 5-8 RBC Status Display 153
- Table 5-4 RBC Status Codes 153
- Status Display 153
- 5.5 PPX:505–6870 RBC 155
- Jumper E1 for 156
- PPX:505–6870 RBC (continued) 157
- Cabling and Wiring the System 166
- 6.1 Cable Routing 167
- Drop line from CPU or RBC 180
- Terminating 180
- Resistor 180
- 6.4 Connecting Modems 197
- 6.5 Connecting to a Printer 199
- Chapter 7 201
- 7.1 Program Storage Options 202
- Note location of notches 207
- Note location 207
- Starting Up the System 213
- 8.1 Powering Up the System 214
- 8.2 CPU Memory Configuration 216
- Number per block 217
- Troubleshooting 221
- System Specifications 246
- ° C (32 to 140° F) 247
- ° C (–40 to 158° F) 247
- Power and Compatibility 251
- B.1 Power Consumption 252
- Power Consumption (continued) 254
- Serial Number 259
- Appendix C 260
- Upgrade Path A 264
- Upgrade Path B 264
- Upgrade Path 266
- Remote Base Controller 272
- Power Supply 272
- FREEZE 273
- (factory set) 273
- Controller 275
- RS-485 I/O 282
- From PLC 282
- I/O BASES 282
- 505–6860 282
- Series 505 and VME Components 283
- D.2 575 VME System Components 287
- D.3 Recommended Spare Parts 288
- Appendix E 290
- E.1 Discrete AC Input Module 291
- E.3 Discrete AC Output Module 296
- °C) Temperature (°C) 297
- E.5 Discrete DC Output Module 301
- E.6 Discrete DC Input Module 304
- Appendix F 306
- Index-2 313
- Index-4 315
- Index-6 317
- Index-8 319
- Index-10 321
Manuais e produtos relacionados com Gateways/controladores Siemens SIMATIC TI500
(94 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais