Siemens ITC Instruções de Operação Página 112
- Página / 132
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Technical specifications
9.4 Technical specifications
Industrial Thin Client ITC1200, ITC1500, ITC1900, ITC2200
112 Operating Instructions, 04/2013, A5E03474888-02
9.4.2 Performance data
Performance values
The performance depends on the network capacity in your system. With the SIMATIC
WinCC Sm@rtServer option, the performance varies within the values specified in the
WinCC documentation.
See also
FAQ 25576569 (http://support.automation.siemens.com/WW/view/en/25576569)
9.4.3 Ambient conditions
9.4.3.1 Transport and storage conditions
Mechanical and climatic conditions for transportation and storage
The requirements regarding transport and storage conditions for the device are more
stringent than those laid down in IEC 61131-2. The following requirements apply to the
transport and storage of the device in its original packaging.
The climatic conditions conform to the following standards:
● IEC 60721-3-2, Class 3K7 for storage
● IEC 60721-3-2, Class 2K4 for transport
The mechanical conditions correspond to IEC 61131-2.
Type of condition Permitted range
Drop test (in transport package) ≤ 1 m
Temperature From –20 to +60° C
Atmospheric pressure From 1080 to 660 hPa,
Corresponds to an elevation of –1 000 to 3 500 m
Relative humidity From 10 to 90%, without condensation
Sinusoidal vibration in accordance with
IEC 60068-2-6
5 to 8.4 Hz: 3.5 mm
8.4 to 500 Hz: 9.8 m/s
2
Shock in accordance with IEC 60068-2-29 250 m/s
2
, 6 ms, 1000 shocks
Note
Avoid dewing
If the HMI device is subjected to low temperatures or extreme fluctuations in temperature
during transportation, moisture could occur on or inside the HMI device. Dewing can occur.
This can cause malfunctions.
The device must be brought to room temperature before it is commissioned. Do not expose it
to direct heat radiation from a heating device. If there is condensation, wait approximately
4 hours until the device has dried completely before switching it on.
Proper transport and storage, installation and assembly as well as careful operation and
maintenance are prerequisites for trouble-free and safe operation of the device.
Non-compliance shall result in the voiding of the device warranty.
- A5E03474888-02 1
- Preface 3
- Registered trademarks 4
- Conventions 4
- Illustrations in this manual 4
- Recycling and disposal 4
- Table of contents 5
- Table of contents 7
- Overview 9
- 1.2 Product package 10
- 1.3 Layout of the devices 11
- Rear view 12
- 352),1(7(WKHUQHW 13
- $XWRPDWLRQV\VWHP 13
- Access to SINUMERIK 14
- Overview 15
- 1.5 Typical applications 15
- 1.6 Requirements 16
- Safety instructions 17
- 2.2 Security information 18
- Procedure 19
- ① Inclined ≤ 35° 21
- ② Vertical 0° 21
- 3.2.4 Checking clearances 22
- Degrees of protection 23
- ,7& 24
- ,7& 24
- ,7& 24
- ,7& 24
- 3.4 Connecting the device 26
- 3.4 Connecting the device 27
- Wiring diagram 28
- *1' 29
- '&9 29
- ① to a server 30
- ① and ② 31
- 3.5 Installing strain relief 32
- Commissioning the device 33
- Special features 34
- Assigning device parameters 35
- Procedure on the device 36
- SSH configuration service 37
- Access without logon 37
- See also 37
- 5.3.1 Access and structure 38
- ④ Open "Help" 39
- 5.3.2 Device data 40
- 5.3.3 System settings 41
- Specifying device name 42
- Setting up screen 42
- Update firmware 43
- Restore to factory settings 44
- 5.3.4 Network settings 46
- Specify network parameters 47
- Use DNS server 48
- Check valid settings 48
- 5.3.5 Connections 50
- Factory default settings 52
- Structure of the tab 53
- Buttons 53
- 5.3.5.3 Connection settings 54
- Functions 57
- 5.3.6 Password settings 58
- 5.3.7 Desktop settings 61
- 5.3.8 Application settings 64
- Proxy bypass 65
- 5.4.1 Introduction 66
- 5.4.2 Installation 67
- 5.4.3 Start 68
- User interface 69
- Copy button 72
- 5.4.4.2 Perform action 74
- 5.4.4.3 Status 75
- Resetting the key 77
- 5.4.6 Assigning a key 78
- 5.4.7 Basic settings 79
- Configuring the server 81
- 6.2 VNC 83
- 6.3 Sm@rtServer 84
- 6.4 SINUMERIK 85
- 6.4 SINUMERIK 86
- Operating the device 87
- 7.2 Front operator controls 88
- 7.3 Operating the taskbar 89
- Taskbar is minimized 90
- Taskbar is hidden 90
- 7.3.2 Starting a connection 91
- ① or bottom 94
- ④ edge of the screen 94
- ② and ③ on the right change: 94
- Operating the device 95
- Removing a USB memory device 96
- Requirement 97
- Cleaning 98
- 8.4 Spare parts and repairs 99
- 8.4 Spare parts and repairs 100
- Technical specifications 101
- FM Approval 102
- Ex approval 102
- Marking for Australia 102
- IEC 61131 102
- Use in industry 103
- Introduction 103
- 9.2.2 ESD guideline 104
- ① Synthetic materials 105
- ② Wool 105
- 9.3 Dimensional drawings 106
- Technical specifications 107
- 9.3 Dimensional drawings 107
- 9.3 Dimensional drawings 108
- Weight 110
- Display 110
- Input device 110
- Memory 111
- Interfaces 111
- Power supply 111
- Miscellaneous 111
- 9.4.2 Performance data 112
- 9.4.3 Ambient conditions 112
- Reducing vibrations 113
- Climatic ambient conditions 114
- Pulse-shaped interference 115
- Sinusoidal interference 115
- Test voltages 116
- Protection class 116
- 9.5.1 Power supply 117
- 9.5.2 USB 117
- 9.5 Description of the ports 118
- Technical Support 119
- A.1 Service and support 120
- Abbreviations 121
- Glossary 123
- Sm@rtAccess/Sm@rtServer 125
- Index 129
Manuais e produtos relacionados com Servidores Siemens ITC
Servidores Siemens BS2000/OSD Manual do Utilizador
(11 páginas)
(11 páginas)
Servidores Siemens BS2000/OSD Informações Técnicas
(47 páginas)
(47 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais