Siemens SITRANS P Manual do Utilizador descarregar pdf (Página 221)

Online Configuration Map for

Siemens SITRANS P DSIII Pressure Transmitter with

Model 375 Field Communicator

5 Config inp/outp, 3 Output 1 Analog output 1 Analog output +

Continued 2 Percent range +

3 Pres xfer function Linear

Sq Rt, lin to Strtpt

Sq Rt, 4 mA to Strtpt

Sq Rt, 2 steps lin to Startpt

NA/4 Startpoint square root

4/5 Zero and Span 1 Zero/Span set 1 Out Scaling PV >1

2 Apply values >2

5/6 Current Limits 1 Lower AO Limit

2 Upper AO Limit

6/7 Alarms / Failsafe 1 AO Alarm / FS Type (Hi/Lo)

2 Alarm / FS LRV

3 Alarm / FS URV

2 Sensor trim points 1 Lower sensor trim point

2 Upper sensor trim point

3 HART output 1 Polling address

2 Num request preambles

3 Num response preambles

4 Local meter 1 Meter type

2 Unit tracking

3 Local Display unit

4 LCD Settings 1 LCD Scaling, if On: 2 LCD Unit

5 Bargraph 3 LCD LRV

4 LCD URV

6 Access Control 1 Local keys control mode

2 Write protect

3 Set write protect --> M

5 Mech. Construction 1 No of electronic changes

Mech = mechanical 2 Design 1 Sensor 1 Fill fluid

2 Isolation material (diaphr)

3 O ring material

4 Module range

2 Remote Seal 1 Number remote seal (RS)

2 RS type

3 RS isolator material

4 RS fill fluid

5 Extension length

6 Extension type

7 Capillary length

3 Process Connection 1 Process Connection

2 DrainVent / plug mat

3 DrainVent / plug pos

4 Process flange bolt

5 Flange type

6 Flange material

4 Electronic Connection 1 Electr housing material

2 Electr connection

6 Diagnosis/Service 1 Status 1 Status summary

2 Extended device status

3 Hardw/Firmw status 1 RAM failure

2 ROM failure OFF = OK

3 Electronic EEPROM ON = Problem

# List continues

4 Diag Alarm Status 1 Calibration Alarm

2 Service Alarm

# List continues

5 Diag Warn Status 1 Calibration Warning

2 Service warning

# List continues

6 Simulation status 1 Pressure simulation

2 El simulation

3 Sensor temp simulation

2 Device 1 Selftest/Reset 1 Selftest --> M

2 Display Test --> M

3 Master reset --> M

4 Changes Config 1 Config changed counter

2 Sensor trim 1 Restore mfgr trims --> M mfgr = manufacturer

2 Sensor trim 1 Sensor trim points 1 Lower sensor trim point

2 Upper sensor trim point

2 Sensor trim 1 Pres zero trim--> M

2 Lower sensor trim --> M

3 Upper sensor trim --> M

3 Trimpoint summary

3 Trim analog output 1 D/A trim --> M

Continued on pg 4 2 Scaled D/A trim --> M

4 Position correction 1 Position corr --> M

3 Simulation/Test 1 Loop test --> M Simulation AO

2 Inputs --> M Simulation Fixed / Ramp

4 Access Control 1 Local keys control mode

2 Write protect

3 Set write protect --> M

Page 3

1 2 ... 216 217 218 219 220 221 222

Comentários a estes Manuais

Sem comentários

Siemens SITRANS P Manual do Utilizador Página 221

Comentários a estes Manuais

Manuais e produtos relacionados com Medição, teste e controlo Siemens SITRANS P