Siemens OSM Guia do Utilizador descarregar pdf (Página 225)

Two attributes under the Logical attributes heading on the System object, Power Regulator

Management Supported and Power Regulator Management Status, indicate whether this feature

is available and enabled.

Insight Control power management is an HP SIM plug-in that can be installed after HP SIM is

installed on the system console. Both HP SIM and Insight Control power management can be

installed from HP Insight Control for NonStop DVD. For more information on requirements and

installation instructions, see the NonStop System Console Installer Guide. For more information on

using Insight Control power management to alter the Power Regulator mode for processor blades,

see the HP SIM for NonStop Manageability.

Extend Problem Incident Report Suppression Time

Extends the duration of suppression by a specified amount of time (in minutes). This action fails if

the suppression was not enabled at that time.

Get SMARTSSD Wear Status Summary

Launches a guided procedure that allows you to view and save a summary of the SMARTSSD wear

status for any or all Solid State SAS disk drives on the system. It displays the same SMARTSSD

Wear Gauge values for each drive as the Show SMARTSSD Wear Gauge action that is available

on individual Solid State SAS disk drives, but this guided procedure allows you to display the

information for multiple (any or all selected) drives in a single interface and to save the resulting

data, if desired, in .csv (or comma delimited) format for use in Microsoft Excel.

Initialize Default Firmware File Names

Starting with H06.12, there are multiple versions of blade firmware on the SUT. The purpose of

this action is to identify the proper blade firmware required for your Integrity NonStop server

configuration while eliminating unnecessary firmware updates for servers that don't need the very

latest blade firmware. This action, displayed only for Integrity NonStop NS14000 series and

NS16000 series servers, must be performed in the following scenarios to ensure that OSM displays

the proper blade firmware version information for your NonStop server:

• If you have installed a new Integrity NonStop NS16200 or NS14200 server. While new

NS16200 and NS14200 systems are shipped with the proper firmware, failure to perform

the action results in OSM reporting this running firmware as Up-rev. Once you perform this

action, specifying NS16200 or NS14200 as your system type, OSM recognizes the running

firmware as appropriate and displays the correct default firmware file names and versions.

• If you are upgrading (either completely or partially) an existing NS16000 server to NS16200

or an existing NS14000 server to NS14200, because the older blade firmware that was fine

for NS16000 and NS14000 does not support the NS16200 or NS14200 (rx 2660) blades.

After migrating to the appropriate RVU to support NS16200 or NS14200, the upgrade

procedure directs you to perform this OSM action. Upon completion of the action, OSM

displays the older running firmware as Down-rev and displays the proper default firmware

file names and versions required for NS16200, NS14200, and hybrid (NS16000/NS16200

or NS14000/NS14200) systems.

If you then need to fall back to your original NS16000 or NS14000 configuration (removing

all NS16200 or NS14200 processors) and want to fall back to your original firmware as

well, you should perform the action again to specify NS16000 or NS14000 as the system

type. OSM will then show the newer (NS16200/NS14200) firmware as Up-rev and original

firmware as the appropriate minimum version to which you can fall back.

• If you are directed by the GMCSC or service provider to perform the action and choose

"Recommended Fix Firmware File Set" from the list of options. This causes OSM to show the

very latest blade firmware available on the SUT as the Default File Version to be used for a

firmware update. This may be necessary to incorporate a recent fix not in the original minimum

base firmware for your system type.

System 225

1 2 ... 220 221 222 223 224 225 226 227 228 229 230 ... 305 306

Siemens OSM Guia do Utilizador Página 225

Comentários a estes Manuais

Siemens OSM Guia do Utilizador Página 225

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Siemens OSM