Siemens v1.0 Manual de Serviço Página 188
- Página / 202
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Example "Motion"
5.6 Expand HMI screen
STEP 7 Basic V10.5
188 Getting Started, 12/2009, A5E02651459-01
3. Change the visibility of the first bottle for the range from "0" to "0" to "Visible".
Leave the visibility setting of the second bottle for the range "0" to "0" at "Invisible".
4. Click the "Save project" button on the toolbar to save the project.
Result
You have set the visibility of the bottles in the HMI screen depending on the signal state on
the "Busy" parameter of the "MC_MoveRelative" instruction.
When the "MC_MoveRelative" instruction is executed, the second conveyor is set into
motion. In this case the "Busy" parameter of the instruction has the signal state "1" and has
the following effect on the HMI screen:
● The first bottle becomes invisible.
● The second bottle becomes visible and moves from the position of the third light barrier to
the second conveyor.
If the "MC_MoveRelative" instruction is not executed, the "Busy" parameter of the instruction
has the signal state "0" and has the follow effects on the HMI screen:
● The first bottle becomes visible and moves from the position of the first light barrier to the
position of the third light barrier.
● The second bottle is no longer visible.
- SIMATIC 1
- TIA Portal 1
- STEP 7 Basic V10.5 1
- Legal information 2
- Table of contents 3
- 1.1 Overview 6
- 1.2 TIA Portal basics 7
- 7,$3RUWDO 8
- 8QLIRUPHQJLQHHULQJV\VWHP 8
- :LQ&&%DVLF9 8
- 67(3%DVLF9 8
- 1.2.3 Data management 9
- Library concept 10
- 1.3 Views in the TIA portal 11
- 1.3.2 Portal view 12
- 1.3.3 Project view 13
- TIA Portal Introduction 14
- 1.3 Views in the TIA portal 14
- 1.4 Example projects 15
- 1.4 Example projects 16
- 1.4.2 Loading a project 17
- TIA Portal Introduction 19
- 1.4 Example projects 19
- Simple example 21
- 2.3.1 Inserting a PLC 23
- Simple example 25
- Network view 26
- Device view 28
- 2.3.3 Configure PLC 29
- 2.4 Create program 31
- 2.4 Create program 33
- 2.4 Create program 34
- 2.4.4 What are networks? 35
- LAD instructions 36
- Normally open contact 37
- Negated coil 38
- 2.4.6 What are tags? 42
- PLC tag table 44
- 2.5 Test program 48
- 2.5 Test program 50
- 2.5 Test program 51
- Additional information 53
- +0, 3/& 3URFHVV 57
- Adding a new HMI device 58
- 2.6 Create HMI screen 59
- 2.6 Create HMI screen 60
- Graphic objects 65
- Use of graphic objects 65
- External HMI tags 66
- Internal HMI tags 77
- 2.7 Testing HMI screen 85
- 2.7.2 Simulate runtime 87
- 2.7 Testing HMI screen 88
- 3.1 Introduction 90
- 3.2 Expanding the program 91
- Normally closed contact 97
- Extended example 100
- 3.2 Expanding the program 100
- 2SHUDQG! 101
- Procedure 102
- Requirements 103
- Introduction 103
- Extended example 105
- 3.2 Expanding the program 105
- On delay 110
- Output coil 110
- 3.4 Expand HMI screen 123
- 3.4 Expand HMI screen 124
- 3.4 Expand HMI screen 129
- 3.5 Simulate HMI screen 132
- Testing in the HMI device 133
- 3.5 Simulate HMI screen 134
- 4.1 Introduction 135
- Use of the PID controller 136
- 4.1 Introduction 137
- STEP 7 Basic V10.5 140
- 4.4 Load simulation block 143
- 4.4 Load simulation block 144
- 4.4 Load simulation block 145
- 4.5 Configure PID controller 150
- Block name 151
- Parameter 151
- 4.8 Adjust HMI screen 158
- 4.8 Adjust HMI screen 159
- 4.8 Adjust HMI screen 160
- Controller optimization 161
- Example "Motion" 165
- Hardware configuration 166
- Example "Motion" 167
- 5.1 Introduction 167
- 5.4 Enable axis 173
- 5.4 Enable axis 174
- 5.4 Enable axis 175
- 5.5 Position axis relative 176
- 5.5 Position axis relative 177
- 5.5 Position axis relative 178
- 5.6 Expand HMI screen 180
- 5.6 Expand HMI screen 181
- 5.6 Expand HMI screen 184
- 5.7 Simulate HMI screen 189
- 5.7 Simulate HMI screen 190
- 5.8 Start diagnostics view 191
- 5.8 Start diagnostics view 192
- 5.8 Start diagnostics view 193
- Glossary 197
- Glossary 199
Manuais e produtos relacionados com Software Siemens v1.0
Software Siemens 270 series Instruções de Operação
(274 páginas)
(274 páginas)
Software Siemens S7-400 Manual de Serviço
(382 páginas)
(382 páginas)
Software Siemens AC65 Guia do Utilizador
(123 páginas)
(123 páginas)
Software Siemens Simatic M7-400 Manual do Utilizador
(266 páginas)
(266 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais